ASTM D7565 PDF

ASTM D describes the requirements for sample preparation, tensile testing, and results calculation of flat fiber reinforced polymer (FRP) composite. Standard. Standard number, ASTM-DDM–10 ; ASTM-DD M– Title, Standard test method for determining tensile. ASTM D/DM() Standard Test Method for Determining Tensile Properties of Fiber Reinforced Polymer Matrix Composites Used for.

Author: Monos Zulunris
Country: Indonesia
Language: English (Spanish)
Genre: Science
Published (Last): 27 January 2014
Pages: 431
PDF File Size: 16.54 Mb
ePub File Size: 5.31 Mb
ISBN: 199-9-22701-713-1
Downloads: 73099
Price: Free* [*Free Regsitration Required]
Uploader: Vojora

ASTM-D, –

Acceptable minimum values for ultimate tensile strength, tensile modulus, and elongation shall not be below the submitted design values unless calculations are performed using the tested values that exhibit an acceptable capacity as per the original design demands and concept. ASTM D can be used to obtain the tensile force capacity and ultimate tensile strain of FRP material used for the strengthening of other structural materials such as, metals, timber, and reinforced concrete.

All defective areas shall be repaired as per Section 3. Alternate finishes must be approved by the owner. Alternate primary carbon or glass fiber systems available upon request. The following editions for this book are d565 available Today, some 12, ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence.

All edges and seams must be feathered. If you like to setup a quick demo, let us know at support madcad. Under certain application conditions, the system may be placed entirely by hand methods assuring a uniform, even final appearance. Section 03 01 satm Saturation shall be supervised and checked by the certified installer.

  AI TOATA VIATA INAINTE ROMAIN GARY PDF

Provide anchorage as detailed on construction drawings, if required. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of ast, standard.

D Terminology Relating to Plastics. SCH fiber — primary carbon fiber, unidirectional. Search book title Enter keywords for book title search. All contact v7565 shall then be cleaned by hand or compressed air. Complete report and submit to Owner, engineer-of-record d75655 FRP composite system manufacturer.

ASTM D7565 Tensile Properties of FRP Matrix Composites for Civil Structures

Are you sure you want to empty the cart? Alternate FRP system manufacturers must provide all items listed in Section 1. Within the text, the inch-pound units are shown in brackets.

FORMAT Single User Subscription Site License Subscription BOOKS All Books PACKAGES All Packages EDITION to PUBLISHER. Certified applicators shall have the minimum experience and written consent by the FRP manufacturer See Section 1.

Fill surfaces with thickened epoxy to eliminate air surface voids greater than 0. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Pre-faced Concrete Unit Masonry. Anchor labels shall have the date of manufacture, the lot number and the minimum weight per unit length for each size.

Gaps between composite bands may not exceed 0. Therefore, maximum force and strain data associated with failure or pullout at either grip are disregarded. If these coupons fail on averagecoupons from the other inch-byinch sample, from the same batch for that day, shall be tested. Combining values from the two systems may result in nonconformance with the standard.

Leave the site clean. Design shall follow criteria in Section 1.

  KAZANTZAKIS THE SAVIORS OF GOD PDF

Where a date is given for referenced standards, the edition of that date shall be used. Copyright Compu-tecture, Inc. Strengthening of Cast-in-Place Concrete Section 03 01 Where no date is given for reference standards, the latest edition available on the date of the Notice of Invitation to Bid shall be used. The average of the tests shall not be less than psi psi for masonry.

There were no books found for the aztm search filters. Well-adhered paint astk concrete do not require removal. The method may be used to determine the tensile properties of wet lay-up and pre-impregnated FRP composites fabricated on site or manufactured in a factory setting. The composite material forms are limited to continuous atm or discontinuous fiber-reinforced composites in which the laminate is balanced and symmetric with respect to the test direction.

Variations in the radius along the vertical edge shall not exceed 0. Review project specifications in detail.

Register for a trial account. Within the text, the inch-pound units are shown in brackets. The contact surfaces shall have no free moisture on them at the time aztm application.

Any batch that exceeds the batch life shall not be used. Filling of large voids in surfaces to receive composite shall be paid as an extra to the contract work of installing the composite system small pinholes or micro-bubbles in the concrete surface or resin do not require special detailing.