FMVSS 208 REGULATION PDF

Subtitle B – Other Regulations Relating to Transportation (Continued) Chapter V – NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION. (a) This standard applies to passenger cars, multipurpose passenger Table 2 of FMVSS or, at the option of the manufacturer if permitted by FMVSS Federal Motor Vehicle Safety Standard (FMVSS) – Occupant Crash Protection establishes performance requirements to determine whether passenger.

Author: Tausida Shak
Country: Honduras
Language: English (Spanish)
Genre: Environment
Published (Last): 2 July 2012
Pages: 215
PDF File Size: 15.75 Mb
ePub File Size: 14.48 Mb
ISBN: 524-4-76226-812-2
Downloads: 5092
Price: Free* [*Free Regsitration Required]
Uploader: Vuran

Any passenger car manufactured on or after September 1, and before September 1, whose driver ‘s designated seating position complies with the requirements of S4.

The inboard receptacle end regulatioon a seat belt assembly installed at a front outboard designated seating position shall be accessible with the center arm rest in any position to which it can be adjusted without having to move the armrest. Let the thighs rest on the seat cushion to the extent permitted fvss the foot movement. Evenflo Right Fit December 1, The accelerometer sensitive axis is parallel to the direction of test platform travel.

Federal Motor Vehicle Safety Standard 208

Impact a vehicle laterally on either side by a barrier moving at 20 mph under the applicable conditions of S8. The means of detachment shall be vmvss key or key -like object.

Each passenger car manufactured on or after September 1, shall comply with the requirement of S4. Extend each line backward and outboard to generate the compliance arcs of the outboard reach envelope of the test dummy’s arms. Under the applicable conditions of S8, mount the vehicle on a dynamic test platform at the vehicle attitude set forth in S If a Type 2 seat belt assembly installed in conformity to this requirement incorporates any webbing tension-relieving regulqtionthe vehicle owner’s manual shall include the information specified in S7.

  MAKITA 9910 PDF

Each application for a temporary exemption rrgulation the inflatable restraint requirements must.

The owner’s manual shall also provide any necessary precautions regarding the proper positioning of occupants, including children, at seating positions equipped with air bags to ensure maximum safety protection for those occupants. All of the test conditions specified in S Postal Service, and vehicles manufactured for operation by persons with disabilities, with a GVWR reguoation 8, pounds or less and an unloaded vehicle weight of 5, pounds or less that is manufactured on or after September 1, and before September 1,shall comply with the requirements of S4.

B The additional information conveyed by the requested label must be specific to the design or technology of the air bag system in the vehicle and not applicable to all or most air bag systems.

In addition, add the amount of Stoddard solvent needed to fill the entire fuel system from the fuel tank through the engine’s induction system. The surface of the block in contact with the heel must have an inclination of 30 degrees, measured from the horizontal, with the highest surface towards the rear of the vehicle.

If the positioning against the instrument panel does not allow the feet to be on the floor pan, the feet shall be parallel to the floor pan. The angle shall be set to Inspect the abdomen to insure that it is properly installed. Set the transverse distance between the longitudinal centerlines at the front of the dummy’s knees at to mm 4.

Federal Motor Vehicle Safety Standard – Wikipedia

With the test dummy positioned in accordance with S If the air bag system contains a multistage inflator, the vehicle shall be able to comply at any stage or combination of stages or time delay between successive stages that could occur in the presence of an infant in a rear facing child restraint and a 49 CFR partsubpart R month-old CRABI dummy positioned according to S The distance between the geometric center of the movable component at the two extreme adjustment positions shall be not less than five centimeters, measured linearly.

  EL GENIO DEL IDIOMA ALEX GRIJELMO PDF

The position of the free end of the belt assembly is recorded. Each vehicle that is certified as complying with S14 shall, at each front outboard designated seating positionmeet the injury criteria specified in S The midsagittal plane of the driver and the passenger dummy shall be vertical and shall coincide with the longitudinal centerline of the bucket seat.

A protection system that meets the requirements of S4. Erect sitting height If the heel of the right foot can contact the floor pan, regulwtion the positioning procedure in a. Line means a name that a manufacturer applies to a group of motor vehicles of the same make which have the same body or chassisor otherwise are similar in construction or design.

This label shall regulatlon in content to the label shown in Figure 7 of this standard, and shall comply with the requirements of S4.

49 CFR 571.208 – Standard No. 208; Occupant crash protection.

The seat cushion reference line angle position may be fmvas through the use of any seat or seat cushion adjustments other than that which primarily moves the seat or seat cushion fore-aft. Side-facing designated seating positions shall be equipped, at the manufacturer’s option, with a Type 1 or Type 2 seat belt assembly that conforms with S7.

Measure and regulatkon the distance between points A and B along the longitudinal centerline of the webbing for the lap belt or lap belt portion of the seat belt assembly.